newsteelconstruction.com

NSC Archives

Technical

New and revised codes & standards: From BSI Updates October 2019

BS EN PUBLICATIONS

BS EN 508-2:2019
Roofing and cladding products from metal sheet. Specification for self-supporting products of steel, aluminium or stainless steel sheet. Aluminium
Supersedes BS EN 508-2:2008

BS EN 10025-2:2019
Hot rolled products of structural steels. Technical delivery conditions for non-alloy structural steels
Supersedes BS EN 10025-2:2004

BS EN 10025-3:2019
Hot rolled products of structural steels. Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
Supersedes BS EN 10025-3:2004

BS EN 10025-4:2019
Hot rolled products of structural steels. Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
Supersedes BS EN 10025-4:2004

BS EN 10025-5:2019
Hot rolled products of structural steels. Technical delivery conditions for structural steels with improved atmospheric corrosion resistance
Supersedes BS EN 10025-5:2004

BS EN 10025-6:2019
Hot rolled products of structural steels. Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition
Supersedes BS EN 10025-6:2004+A1:2009

CORRIGENDA TO BRITISH STANDARDS

BS EN ISO 3581:2016
Welding consumables. Covered electrodes for manual metal arc welding of stainless and heat resisting steels. Classification
Corrigendum, August 2019; Corrigendum, May 2018

UPDATED BRITISH STANDARDS

BS EN 1993-1-5:2006+A2:2019
Eurocode 3. Design of steel structures. Plated structural elements
Amendment, September 2019; Amendment, July 2018

BS EN ISO 15614-1:2017+A1:2019
Specification and qualification of welding procedures for metallic materials. Welding procedure test. Arc and gas welding of steels and arc welding of nickel and nickel alloys
Amendment, August 2019; Corrigendum, May 2018

BRITISH STANDARDS REVIEWED AND CONFIRMED

BS ISO 15510:2014
Stainless steels. Chemical composition

BS ISO 16143-2:2014
Stainless steels for general purposes. Corrosion-resistant semi-finished products, bars, rods and sections

BS ISO 16143-3:2014
Stainless steels for general purposes. Wire

BRITISH STANDARDS UNDER REVIEW

BS EN ISO 1127:1997
Stainless steel tubes. Dimensions, tolerances and conventional masses per unit length

BS EN ISO 3452-5:2008
Non-destructive testing. Penetrant testing. Penetrant testing at temperatures higher than 50°C

BS EN ISO 3452-6:2008
Non-destructive testing. Penetrant testing. Penetrant testing at temperatures lower than 10°C

BS EN ISO 9445-1:2010
Continuously cold-rolled stainless steel. Tolerances on dimensions and form. Narrow strip and cut lengths

BS EN 10266:2003
Steel tubes, fittings and structural hollow sections. Symbols and definitions of terms for use in product standards

BS EN 10349:2009
Steel castings. Austenitic manganese steel castings

BS EN ISO 11126-9:2004
(BS 7079-F9:2004)
Preparation of steel substrates before application of paints and related products. Specifications for non-metallic blast-cleaning abrasives. Staurolite

BS EN ISO 11474:2014
Corrosion of metals and alloys. Corrosion tests in artificial atmosphere. Accelerated outdoor test by intermittent spraying of a salt solution (Scab test)

BS EN ISO 11782-1:2008
Corrosion of metals and alloys. Corrosion fatigue testing. Cycles to failure testing

BS EN ISO 11782-2:2008
Corrosion of metals and alloys. Corrosion fatigue testing. Crack propagation testing using pre-cracked specimens

BS EN 14532-1:2004
Welding consumables. Test methods and quality requirements. Primary methods and conformity assessment of consumables for steel, nickel and nickel alloys

BS EN 14532-2:2004
Welding consumables. Test methods and quality requirements. Supplementary methods and conformity assessment of consumables for steel, nickel and nickel alloys

BS ISO 14347:2008
Fatigue. Design procedure for welded hollow-section joints. Recommendations

NEW WORK STARTED

EN ISO 898-2
Mechanical properties of fasteners made of carbon steel and alloy steel. Nuts with specified property classes. Coarse thread and fine pitch thread
Will supersede BS EN ISO 898-2:2012

EN ISO 14341
Welding consumables. Wire electrodes and weld deposits for gas shielded metal arc welding of non alloy and fine grain steels. Classification
Will supersede BS EN ISO 14341:2011

EN ISO 15792-1
Welding consumables. Test methods. Test methods for all-weld metal test specimens in steel, nickel and nickel alloys
Will supersede BS EN ISO 15792-1:2008+A1:2011

EN ISO 15792-2
Welding consumables. Test methods. Preparation of single-run and two-run technique test specimens in steel
Will supersede BS EN ISO 15792-2:2008

Print Friendly, PDF & Email

Share this post

THIS MONTH'S MAGAZINE

Click on the cover to view this month's issue as a digimag.

Archives